Alarm Lock Tech

DL Windows and Networx webinars set for August 6-8

There are new webinars scheduled for May 28-30. These live webinar sessions will cover the DL Windows software. Session 1 on May 28 will cover how to create an account and lock profiles as well as how to add users to the Global Users area. Session 1 will also show how to program the legacy locks with the AL-PCI2U cable and/or the DTM III module.

Session 2 will cover how to set up schedules including passage (open) mode, group and user enable and Open Window schedules. The session will also cover the Features of the locks such as Group 2 toggles passage mode.

Session 3 is on the Networx locks. This session will cover how to discover the gateways and locks. The Global Emergency Commands will be discussed and shown. These include lockdown, passage and return to normal.

All 3 sessions will be presented 3 times per day, 10 am, 1 pm and 7 pm Eastern Time. Don't miss out on these popular and valuable trainings.

 

If you would like to attend one of these sessions, click this link.

How do I pair a wireless remote to a Networx PL lock?

The following pairing procedure assumes the PL Networx lock has been powered and at least one Administrative User proximity credential (Users 2-11) has been enrolled into the lock (its DL-Windows Lock Profile downloaded into the lock). Keep this proximity credential physically available, as it will be used during the below procedure. Note: The following procedure is unique to the PL Networx lock and is NOT supplied with the programming instructions included with the remote release (RR-1BUTTON, WI1999 and RR-4BKEYFOB, WI2004).

Proceed as follows:
1. Disconnect the lock battery connector.
2. Short the two white wires (Remote Input wires) together for 10 seconds to ensure discharge of all capacitors. After 10 seconds, remove the short.
3. Re-connect the battery pack. The lock immediately sounds 3 short beeps (if these 3 beeps are not heard, start again at step 1). Over the next 7 - 9 seconds, the lock performs its power-up self-test, and indicates it is ready to operate by sounding 7-beeps.
4. At the lock proximity reader, present the enrolled Administrative User (Users 2-11) proximity card. The lock unlocks and enters a 30-second "remote release enroll sequence" during which the green LED flashes.
5. With the remote release in hand, observe the remote release LED as you perform the next steps:
a. Press and hold a remote release button.
b. The remote release red LED lights...keep holding the button…
c. When the remote release LED flashes green, release the button...
d. Wait a few seconds...observe the LED as follows:
·  LED solid green = Pairing successful. To pair another button, go to step 1.
·  LED solid red = Pairing unsuccessful. Start again at step 1.

After step 5, the lock will exit the "remote release enroll sequence" and will return to normal operation

  

PL6100 locks must have at least 59.d firmware

ETPLN locks must have at least 63.d firmware

PL6500 locks must have least 60.f firmware

 

For more information about Networx lock firmware versions and to download the firmware, go to www.alarmlock.com and click on Resources.

 

Andy Phelps, CRL, CAI

Alarm Lock National Training Manager

Mini training videos available now

I would like to announce the Alarm Lock YouTube channel is up and has video training sessions on how to program the Alarm Lock Trilogy locks and how to use DL Windows programming software. Videos include how to change the master code in a DL2700 lock, how to activate passage mode in the T2 and T3 locks at the keypad and several topics on how to use the DL Windows software to program the Trilogy locks.

Click here to go to the Alarm Lock YouTube channel and subscribe. More videos will be added when they are completed. If you have a topic that you would like to learn more about, you can either post a comment on the channel or you can post your topic suggestion on this site.

Andy Phelps, CRL, CAI

National Training Manager

Alarm Lock Systems, Inc.

Do I need to upgrade the firmware in my gateways and locks?

The answer is YES. When new firmware becomes available for either the Alarm Lock Networx gateways or locks, you should upgrade. There are many reasons why but the most important is to keep the products up to date with the latest features.

When we create new versions of the DL Windows software, the Networx locks and gateways may have new features available such as remote lockdown. We also have new products such as the Generation 2 gateways and expanders that, if the locks have old firmware, may not work properly with these new items.

To see what version of firmware is installed in your gateways or locks, open DL Windows and then open "Gateway Config". The gateways will be listed and the current firmware version installed will be displayed. To find the installed firmware version of the locks, open the "Gateway lock table" and each lock assigned to that gateway will display the current firmware version.

Now go to the Alarm Lock software website, here, and compare your model of gateways and locks firmware with the most current. Now download the latest version of firmware and upload the firmware to the gateways or locks. NOTE: You may need to perform a full upload of the programming once the firmware is upgraded. It is recommended to do this even if explicit instructions don't indicate that you must.

Here is a list of the some of the latest versions of firmware:

AL-IME, AL-IM80211, AL-IMPOE, AL-IMPOEP gateways - 3.95

PDL6100 - 55.s

DL6100 - 56.k

PDL6500 - 57.i

Networx Panel - 64.t

Networx DK/PDK keypad - 65.e

PDL6200 - 67.k

ETPDLN - 61.l

ArchiTech N90 - 85.a

ArchiTech N95 - 83.l  NOTE: This version may cause the lock to work in reverse. Check with your local rep to determine if you need to replace the lock body. Click here to find your local factory representative.

 

Andy Phelps, CRL

Alarm Lock National Training Manager

 

DL Windows 5.4.2 now available

I would like to announce that the latest version of DL Windows is now available for download from the Alarm Lock website. This new version of DL Windows will allow you to use the new version 2 Gateway and Expanders. It also has a back up reminder that can be set to remind you to back up your database daily, weekly, bi-weekly or monthly. This version is fully qualified for Windows 10 and Windows Server R2 (2012) and users can upgrade directly from 5.1.1 , 5.2.3, 5.3.3 or 4.1.96.There are to many new and upgraded features to list.

Click here to go to the Alarm Lock software website and download your copy today so you will have all the advantages and abilities of this new version of DL Windows.

Also, there are new firmware updates for the DL6100, PDL6100 and PDL6200 Networx locks available as well. Upgrade the firmware in your locks to get the most out of your Alarm Lock Networx system.

If you don't have access to the tech site, register and get access to not only the software and firmware updates but also tech notes, programming manuals and much more.

 

Andy Phelps, CRL

National Training Manager

Alarm Lock Systems, Inc

Why do the batteries in my Alarm Lock Trilogy lock drain faster than expected?

Batteries that tend to drain quickly are often the result of either a simple mechanical issue or a programming oversight. 

Mechanical

• Check for wiring issues such as frayed wires that are shorted under the mounting bracket or broken strands of wire at the connecter pins.
• Check for corrosion inside the battery pack or on the battery holder terminals.  Corrosion can cause resistive shorts.

Programming

• Many lock models are equipped with an internal relay, and it is possible this relay may have been previously programmed to energize upon a lock event.  Energizing the internal relay repeatedly or for extended periods will quickly drain the batteries, therefore locks that are programmed to energize the relay should be wired with external DC power.  Otherwise, you may wish to consider reevaluating the use of features responsible for the relay activation, and if needed, disable all relay functions using either DL-Windows software or through the lock keypad (see the printed programming instructions for details).  Always observe all warnings detailed in the programming instructions for these relay features before programming your lock.

DL Windows and Networx webinars coming soon

If you want to learn more about the Alarm Lock DL Windows software or the Networx locks, then now is the time to sign up for an upcoming series of webinars that will teach you the basics and some tips on how to use the software.

Starting June 21, the webinars will be 3 times/day, 11 am, 2 pm and 5 pm EDT. There will be 3 days in the series. You pick the time of day that fits into your schedule, about 1 hr, and you will learn how to operate the DL Windows software and Networx locks.

The schedule will be: Tuesday June 21 - DL Windows version 5.2.3 - Creating accounts and users

                                Wednesday June 22 - DL Windows version 5.2.3 - Creating schedules and lock features

                                Thursday June 23 - Networx connectivity

Here is a brief description of the sessions:

    DL Windows version 5.2.3 - Creating accounts and users: This webinar will teach you how to create a new account and add users to the software, both manually and using the CSV import utility. The utilization of manager, one time use and other special codes in the Administrative screen are also included. We will discuss Group assignments for users and what the group assignments are used for and how to program the Trilogy locks via the computer or DTM III.
Other topics discussed will be software users and their privileges in using the software from remote workstations.

    DL Windows version 5.2.3 - Creating schedules and lock features: This webinar will discuss schedules and features of the Trilogy locks via the software. Included will be how to set up a basic schedule, 1st person in schedule and Holiday schedules. We will discuss what each type of schedule is and how they are implemented in the locks.

    Networx connectivity: This session will discuss the Alarm Lock Networx locks which includes the Trilogy and ArchiTech locks. The gateway connection and discovering of locks will be shown. We will send programming and retrieve an audit trail via the network.
The sending Global Emergency Commands including Lock Down, Passage and Return to normal will be demonstrated.

To sign up for one of these valuable training sessions on DL Windows and Networx locks, click here and you will be taken to the sign up page.

 

Andy Phelps, CRL

Alarm Lock National Training Manager

New webinars coming Jan 5-7, 2016

I have another set of webinars coming up Jan 5-7, 2016. Follow the link below to access the registration for the very informative live webinars. You can follow along on your computer and ask questions.

The webinars on Jan 5 & 6 will cover DL Windows v 5.2.3 on how to set up accounts, add users, set up schedules and some of the most frequently used features. The webinar on Jan 7 will cover the manual key pad programming of the T3 Trilogy locks. Adding users, passage modes, adding schedules and other features of the locks will be covered.

 

This link, webinars, will take you to the Professional Training calendar page to view the times available for each webinar. Also there you will find a button to view previously recorded webinars on T2 manual programming and DTM III usage. You can watch or download the webinar for viewing any time.

 

Andy Phelps, CRL

Alarm Lock National Training Manager

New DL2700LD now available

I would like to introduce the newest Trilogy lock available, the DL2700LD. This lock, part of our School Security Solution, has the capability of a "local" lockdown and has a wireless remote release built in. The DL2700LD has a new battery cover with an LED light bar that flashes red when the unit is in lockdown.

The 4 button remote, that is included, can be programmed into 4 different locks at the same time for remote release (remote receivers will be needed for non lockdown models). Also, a "lockdown" of up to 4 DL2700LD locks within range can occur with a simple pressing of 2 buttons.

The 4 button remote may be used as a momentary release or changed to a "passage toggle" function.

While in lockdown, only the Master code and managers codes will open the door, locking out all basic users.

The lock also has the option to have a "Chirp" sound for 30 seconds during lockdown.

Contact your local rep for additional information about the new lock and availability.

 

Andy Phelps, CRL

National Training Manager

Alarm Lock Trilogy and DL Windows Webinars

My travels across the nation have allowed me to meet a lot of people and train them on all the Alarm Lock Trilogy products as well as the DL Windows V.5.2.3. But there are still a lot of places that I have not been able to get to or you may not have been able to attend the training sessions in your area.

Here is your opportunity to get some of the same training without the commute or being out of pocket for an entire day.

I am now offering webinars that last about an hour. You can attend from the comfort of your home or work place. Follow the link below to see a list of upcoming sessions available.

http://www.alarmlock.com/seminars

The sessions consist of the following topics: DL Windows V. 5.2.3, Data Transfer Module usage, T2 Manual key pad programming, Networx Connectivity and many more.

The sessions are usually scheduled one week a month at 11am and 6pm eastern time.

So, check the schedule for dates and times of all the upcoming Webinars and on site trainings available. Check back often as more dates are being added all the time.

I hope to see you at a local training session or "hear" you on a webinar.